XLT.fora.pl

hektor · Wysłany: Pią 22:41, 17 Mar 2006 Temat postu: programy z netu dla DFX

witam
jestem początkującym użytkownikiem DFX-a w sieci znalazłem kilka programów które trzeba sprawdzić będe je wrzucał sukcesywnie
na początek program Baz-a z forum "DFX only "

It's taken 3 months of non-stop research and experimentation, but I have finally settled on a program that runs stable, and gets deep. Here it is. Some settings will change depending on your conditions....

Target Volume = 50 (I have my headphones turned all the way up)
Audio Threshold = 15
Tone (Audio Freq.) = 231
Audio Disc. = ON
Silent Search = OFF
Mixed-Mode = OFF
A.C. Sensitivity = 80
D.C. Sensitivity = 35
Backlight = 0
Viewing Angle = 25
Ratchet Pinpoint = OFF
S.A.T.Speed = 5
Tone I.D. = ON
V.C.O. = ON
Modulation = ON (IMPORTANT FOR STABILITY)
Autotrac = ON
Trac View = OFF
Autotrac Speed = 8
Autotrac Offset = 0
Trac Inhibit = ON
Coarse G.E.B. = AUTO
Fine G.E.B. = AUTO
Disc. Edit, Block Edit = REJ. -95 - -71, ACC. -70 - +95
Recovery Speed = 15-25 (15 for clean areas, 25 for very trashy)
Bottlecap Reject = 1
Hot Rock Reject = 10-20 (If you can run 10 without +94 and +95 noise coming through, then do so)

Sweep Speed = 1
Ground Filtering = 4
Visual Disc. = OFF
Icons = OFF (User Preference)
V.D.I. Sensitivity = 95
D.C. Phase = ON
Graph Averaging = OFF
Graph Accumulate = ON
Fade Rate = 5
Preamp Gain = 4
2 Frequency (Best Data) = OFF
2 Frequency (Correlate) = OFF
V.D.I. Normalized = ON
1 Frequency (3Khz) = ON
1 Frequency (15Khz) = OFF

NOTES: With modulation on, you should be able to run preamp 4 and AC sens of at least 70 and have no problem with high pitch noise from +94 and +95 breaking through the threshold audio. If you do, first try turning up hot rock reject to 20 and if that doesn't work, lower vdi sensitivity to no lower than 85. You should not have to reject +94 with these settings. The EMI should be no louder than the threshold volume.

miraul

witam. pare uwag
ten program jest chory . Wink

ac sens 80 - preamp 4 - osobno przy takim ac i przy takim preampie nie da sie szukac a co dopiero w polaczeniu -efekt wykrywacz reagujacy na niewiadomo co niestabilnymi wskazaniami.
discriminacaj od -71 do +95 - to po co wogole wlanczac dykryminacje -przy takim ustawieniu ciagnie wszystko.
treshold jak dla mnie tez za wysoki ale to kwestia gustu.
pozdr

Van Worden

Witam!

Miraul, a testowałeś go już? Gościu pisze w uwagach żeby AC Sens, ustawić na 70 i gdyby były fałszywe sygnały, ustawić hot rock reject na 20.. Jeśli to nie pomaga, zmniejszyć VDI na 85.. No i pisze, żeby program dostosować do własnego terenu..
Dajcie znać jak faktycznie ten program sprawuje się w terenie

Pozdrawiam

VW